Change Watch Battery Now I Cant Get Back on Again Without Pres

Download Article

Download Article

Depending on the scout, changing the battery to get information technology ticking again is often a simple task that y'all can exercise at habitation with a few tools and the proper techniques. Going to a scout repair shop and having a specialist change the battery is expensive and time-consuming, but you nearly likely can do it yourself. The method for changing the battery will change based on the brand, type, and style of your particular watch. Past taking the proper precautions and advisedly post-obit the correct methods, you tin can quickly and easily replace a faulty or dead battery in your favorite sentinel.

1. one

   Find the small indentation on the back of the lookout. Turn the picket over and find the minor pigsty or indentation that's on the side of the sentry, between the spotter dorsum and the lookout itself. This indentation is created specifically to assist you pry off the back of the watch.

   • If y'all tin't discover the indentation, scan the backside of your lookout with a magnifying glass.
   • Wear a pair of grit free latex gloves when replacing your bombardment.

2. 2

   Sideslip a sharp tool into the indentation. Detect a tool that's pocket-sized plenty to fit into the indentation you discovered. Tools like a small flathead screwdriver created for eyeglasses or a small-scale blade may fit information technology into the indentation.^[1]

   Advertisement

3. 3

   Twist the tool to pop off the back casing. Apply the blade or the screwdriver similar a lever to pry up one side of the watch back. In one case it comes loose, you can take hold of onto information technology with your hand to carefully remove the dorsum of the watch.^[two]

4. 4

   Snap the back of the sentinel back into the casing. After you replace the bombardment, align the dials on the side of the watch with the indentations on the dorsum of the lookout man. Press down heavily on the watch back until information technology snaps dorsum into identify.^[iii]

   • It's important to line upwardly the dorsum of the watch perfectly or yous run the risk of damaging the scout's internal parts.
   • Some watches require a spotter press to reattach the back to the sentry.

   Advertizing

1. i

   Unscrew the screws from the back. At that place should exist small screws on the backside of your sentinel. These screws proceed the dorsum in place. To remove them, utilize a small screwdriver that you lot would utilise for eyeglasses and plow the screws until y'all can remove them from the watch.^[4]

   • Make certain to put the pocket-size screws in a safe identify, like a ziplock bag, so that you don't lose them.

2. ii

   Remove the back plate. One time y'all remove all of the screws from the dorsum of the lookout man, the back should hands lift up. This will expose the watch battery and other internal parts in the lookout man.^[5]

3. 3

   Rescrew the screws into the back of the watch. Once you replace the battery, press the back of the watch back onto the watch and accept the small screws that you removed earlier and screw them dorsum into their holes.^[6]

   Advertisement

1. 1

   Locate the indentations on the back of the watch. There should be slots on the back of the watch that are big plenty to fit the edge of a coin. These are created intentionally for like shooting fish in a barrel opening of the watch dorsum.^[vii]

2. 2

   Insert a quarter into one of the slots. Place the edge of the quarter into the indentation on the dorsum of the picket. If information technology doesn't fit, apply a smaller coin like a penny or dime.^[8]

3. 3

   Rotate the coin counter clockwise. As you rotate the coin, the small screw on the back of the watch should come up up and the back should disengage from the sentinel.^[9]

4. 4

   Remove the picket dorsum. Use your easily to carefully elevator upward the backside of the watch. Make sure that you rotated the coin slots a full turn or the back won't come up loose.^[x]

   Advertisement

1. i

   Get a brawl of thumb tack or glue tack. You lot'll demand to get a brawl of a sticky thumb tack or glue that will attach to the dorsum of the lookout man and help you rotate it. You lot can purchase this at well-nigh craft stores or online.^[xi]

   • At that place are as well grip-balls that are fabricated specifically to open the back of a screw off sentry.

2. 2

   Press the tack against the back of the sentinel. Knead the tack until it'south soft and gluey. Printing it hard confronting the dorsum of the watch.^[12]

3. 3

   Twist the tack counter clockwise and twist off the back. Once the tack is fastened to the back, twisting it counterclockwise should loosen the back of the scout until it's not attached.^[13]

   Advertizement

1. ane

   Undo the strap and turn the watch over. Information technology's easier to work with the spotter if yous're unobstructed. Disengage the strap or remove the ring completely and turn the spotter over.^[14]

2. 2

   Remove the back of the lookout man. 4 types of spotter backs include snap offs, screw-off backs, swatches, and backs with screws holding them together. Examine the back of your watch to determine what kind of watch you lot have.^[15]

   • Screw off backs will have notches around the edges on the back of the watch.
   • Snap offs will have a completely smooth dorsum with a small-scale cut or indentation where the back of the sentinel run into and spotter meet.
   • Swatches will accept a slot on the back where you can fit a coin.

3. three

   Remove whatever prune that may be holding the battery in place. In one case you lot remove the back, you'll exist able to run into the internal components of the watch. Oftentimes, there volition exist a something blocking the battery from slipping out. This could exist a prune, retaining bar, and plastic encompass.^[xvi] Look at the lesser of the clip to detect the small-scale pigsty near the bottom of the clip. Insert a small screwdriver into the pigsty and press up with your screwdriver to undo the clip. This should make your battery accessible.^[17]

   • Article of clothing a pair of dust costless latex gloves when replacing your battery.
   • Some watches won't have anything covering up the battery. In this case, you lot can skip this footstep.

4. 4

   Take observe of the position of the battery. Before removing the battery, have annotation of its position and which side is facing up. Take a look at the writing on the battery and then that you know which kind you should get to supervene upon it. The battery will be circular disc that'southward around 3/8 of an inch (9.5 mm).^[18]

5. v

   Ease the battery from the casing. Using plastic tweezers, position one side of the tweezers nether the battery. Pry up with the tweezers to remove the battery from its casing.

6. 6

   Push the new battery into identify. Take your replacement battery and stick information technology in the spot where your old bombardment was. Employ the plastic tweezers to press information technology back into place. Avoid hit or disrupting the other internal parts of the watch.^[19]

7. 7

   Check that the spotter works before reattaching the back. If the watch is non working, y'all may have put the battery in backward, or information technology could exist damaged. Double check that the battery is incorrectly installed. If information technology still doesn't work, consider taking information technology to a professional for repair.^[xx]

   Advertizement

Add New Question

• Question

  Exercise I need a special tool to remove the back of my watch?

  

  Ordinarily, a very fine tip flat head screwdriver is what you need. You can get a ready of fine Philips and flat drivers in what is often referred to as a "jeweler'due south" screwdriver ready, normally for under $5.00 (US).

• Question

  I accept a timex that I replaced the bombardment in, however, now I can't get the dorsum piece to snap back on.

  

  Make sure that you're properly lining up the dials on the spotter earlier applying a lot of pressure level with your fingers onto the back of the spotter. You might demand a special tool to utilize more pressure if it'southward not properly snapping back on.

• Question

  I bought a new bombardment but information technology doesn't sit snug in the case. It worked when I held it downward but when I put the cover on, it didn't piece of work. Why would it exist a wobbly fit?

  

  The battery could be non right 1, or the battery holder is broken. Go to a watchmaker for further assist.

• Question

  What do I do if it doesn't have a removable dorsum-end?

  

  It has to be removable. If it has screws, unscrew it. If it doesn't have screws, await on the side of the cover for a flap or a office that'southward like a flap, or an open space. Use a knife or something to pry it open. If you tin can't pry it open, then go to a watchmaker to open it. Now the pry open kind of watches are hard to put back, and then exist super careful.

• Question

  What can I exercise if I can't get the screws on the back of my watch out?

  

  Go to a watch store, and enquire them to try to get it out for y'all. Information technology might accept rusted shut, and so information technology might not piece of work.

• Question

  Can I use AAA battery number 2025 to replace a battery number 934?

  

  No. This battery is used to supplant 280-205, 5003LC, BR2025, DL2025, ECR2025, and SB-T14 batteries.

• Question

  How and where do I become a proper battery if the sometime one was missing?

  

  If you have a jewelry store near you, go there and ask for a watch battery. Be sure to tell them what the brand is so they know what to get for your sentry.

• Question

  Can a person'due south body pull out the charge from a watch battery?

  

  Your lookout man can be affected by static electricity or electrical equipment, merely non your body.

• Question

  Will this work on a Timex sport watch?

  

  Yeah.

• Question

  What size screw is usually used to hold prune on bombardment? I lost i while trying to replace battery and would similar to buy the screw

  

  Watch screws are anywhere between .30mm and i.20mm. Have your watch to a professional person so they tin can test different screws and determine what one you need.

Bear witness more than answers

Ask a Question

200 characters left

Include your electronic mail address to become a message when this question is answered.

Submit

Advertisement

Things You'll Need

• Plastic tweezers
• Jeweler'southward screwdriver
• Dust free latex gloves
• Magnifying drinking glass (optional)
• Replacement battery

Cheers for submitting a tip for review!

• If you accept an expensive watch, consider taking it to a professional instead of replacing the bombardment yourself.

Advertisement

About This Article

Article Summary X

To change a scout battery, effigy out if the scout back snaps off or if it'south held in place by screws, then remove it accordingly. If there's a clip holding the battery in place, insert a minor screwdriver into the hole and press upward to disengage it. Then, pry the one-time battery out of the casing with plastic tweezers, discard it, and push the new bombardment into place. Exist sure to check that the watch is working before reattaching the back! For tips on removing different kinds of lookout backs, read on!

Did this summary assistance yous?

Cheers to all authors for creating a folio that has been read 1,263,864 times.

Did this article assist you?

cochranartilegive2000.blogspot.com

Source: https://www.wikihow.com/Change-a-Watch-Battery

Share this post